Click a component to inspect it.
Design notes
Centred 96 mm grid with at least half-pitch edge margins. Outer centres are 84 mm from the ends and 66 mm from the long edges. Perimeter rails and three crossmembers sit between grid lines. Four holes over legs are omitted; clamp-body clearance requires checking the actual clamp. Drill both sheets separately with the same registered grid.
Future MATCHFIT track centrelines only, not cuts: midway between the 96 mm dog-hole lines. Owner has accepted the 16 mm MDF for this use; tracks remain reserved for later routing. Black crosses show 24 proposed 4 × 30 mm MDF-to-plywood screws, offset a quarter pitch from dog centres and track lines. No glue. Keep saw paths clear of screws; these markings do not define a safe cutting lane.
The removable plywood insert fills one end of the bench. Its two side panels rest on the lower shelf, its back braces the insert and its top forms the middle shelf. Check the intended storage fits before fixing the insert height; the model currently places it midway in the opening.
Owner accepted 16 mm MDF for MATCHFIT on 2026-10-01 in codex task 01a0c8f7-7301-75a3-9a9f-48422c7147f0. This is an owner design decision, not manufacturer certification. Add removable clamping panel at the end opposite the half shelf and removable tool holders beside the shelf. View proposal: panel height is four dog-grid pitches; plywood backing matches the structural top. Holster openings and mounting hardware need fitting to the actual tools; castor pedal sweep and attachment hardware need checking. Accessories are proposed geometry, not a final cutting schedule.
Owner correction 2026-10-06, task 01a0c8f7-7301-75a3-9a9f-48422c7147f0: retain both horizontal sheets at 1800 × 900 mm. Extend the doubled upper frame to the top edge at the panel end; four upper long rails are 1688 mm. Place the 21 mm plywood-backed 16 mm MDF vertical panel outside that edge, with its top flush: total length including panel is 1837 mm. End-panel blanks remain 900 × 421 mm. Legs and lower frame remain unchanged. Cleats run along the other three sides. Vertical grooves load from above; top grooves load from the opposite end unless a separate entry detail is designed. Panel bolts remain provisional and drilling is deferred until after the main table is built.
Corrected removal geometry, 2026-10-02, task 01a0c8f7-7301-75a3-9a9f-48422c7147f0. The former pads below the fixed cleat blocked lifting and are superseded. Holder backplates now stand outward by one plywood thickness, with upper packing behind the mating cleat and bearing pads against the FRONT face of the fixed cleat. Pads slide beside the rail, not beneath it. Remove retaining knobs completely, lift 31.5 mm (derived from 1.5 times nominal plywood thickness), then pull outward. This leaves 10.5 mm disengagement above the bevel and 4.5 mm clearance beneath the plywood top. Dimensions are nominal: confirm fit with actual stock. Three fixed 45-degree cleats remain directly on the 120 mm upper frame, excluding the vertical-panel end. Future wall rails must match this bearing arrangement as well as the bevel. Fixing sizes, loads and plywood allocation remain to detail. Outer dogs and clamp swing require checking with actual accessories.
Owner accepted plain crossbar with recessed panel screws and captive nuts on 2026-10-01, task 01a0c8f7-7301-75a3-9a9f-48422c7147f0. Supersedes MATCHFIT mounting tracks and entry notches. Counterbore/clearance sizes retained as plan-based visual placeholders pending chosen bolt heads, washers and nuts. Hardware glyphs are illustrative; select exact sizes and verify wrench access before drilling. Tray and holster use French cleats; wall installation remains future work. Owner sequencing decision 2026-10-06, task 01a0c8f7-7301-75a3-9a9f-48422c7147f0: build the main table first; resolve and fit the vertical panel attachment afterwards. Reserve its envelope but do not drill panel bolt holes yet.